It uses the drawings below to be able to be made familiar to the location
of the keyboard keys

ALL THE VERSIONS EXCEPT
U.k. E EUROPEAN VERSION

THE BATTERY
OBS:
Surrounding ratura of 5C recharges the batteries with tempe- ~ 40C.
Recharges is
of this band they will be able not to load tota lmen-
you the batteries
1 Battery of NiCd (PB-13)
Before using its radio for the first time
an full load in the battery will be necessary
therefore the same one never received load some Pará
ra that you it can enjoy of the greater I number
of possiveis loads and dumps.

2 Recharge
It inserts plug of the loader (BC-14) in termi-
nal in the upper part of the HT. Conecte carre-
gador to the taking, and never leaves the extreme load
to pass a period of 15 hours. The time of
util life of its battery can be diminuido if
the period of recharge to exceed the time re-
comendado.

3 Installing the battery
Infe- inside inserts the battery of the HT for the part
rior of the same one until feeling one click, in this way
the battery must be stopped inside of the one with
partimento of the HT.
To remove the battery of inside of the HT
it turns it coasts and it pulls the existing constraint there
for the right until she is set free the same one.

4 Nivel de Voltagem of the Battery
Putting indicates the relative voltage of the battery
during the transmission.
It recharges or it changes for another battery
when the pointer of nivel will be low.

Package of NiCd Batteries

Approach Condition

5 Running time of the Batteries (hours)

This time is based on 6 seconds of transmission 6 seconds of reception, and
48 seconds without receiving sign some, and with the volume in the maximum
besides being active the Saver function.
CARE
If the display will be blinking and bipando and voce not to obtain
disconnect the radio atravéz of keyboard key POWER it is sign of that the
battery is depleted, it removes the battery of inside of the radio or
places it in recharge.
The battery always sends regards to unload all so that if it can recharges
it again, preventing thus the effect memory.

OPERATION IN RECEPTION MODE
1 Binding the radio

It places the battery and the antenna in its places

It pressures the POWER keyboard key to bind the radio.
When binding the radio must appear in the display
since that already he has not been reprogramado,
the following one:

2 Controls of selector and volume
This radio possesss two controls one stops
volume and another one for selector (since that not
reprogramado)
They will go to control the selector volume and of
band who will be with the indication of PTT
.

If voçê to pressure keyboard key BAND, the controls will pass to the band
of VHF.Se voçê to preesionar keyboard key E.chg will be able temporarily to
pass the controls for the band who this with the PTT pointer and thus that
voçê will not be more using no function the controls will not return for
the band with the indication of PTT.
Splitting of the volume control

It pressures keyboard key F and after that keyboard key E.chg

Splitting of the control of selector

It pressures keyboard key F and after that keyboard key E.chg

Returning for the original mode

It pressures and it holds keyboard key F for more than
as and it pressures keyboard key E.chg.

x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-x-r
> < / px

Smoothing of the Squelch

The Squelch helps to eliminate the ruido one white and static that is not
very agradaveis.
The Squelch is an automatic silencer that when a small sign will be being
received it it unlocks and when we will not have more signs it stops in
silence mode.
Its radio has two controls of Squelch, one for each band.

1-Gire the control of Squelch of the desired band
total in the counter-clockwise direction, of this
mode the Squelch the this opened and LED indi-
cador must be lighted in the green color.

2-Gire the button of volume for until the sound
either of good level.

Lentamenteo 3-Gire control of Squelch in
clockwise until the LED deletes and
ruido it disappears, this position of the Squelch
it is called Point I criticize of the Squelch.

5-Se voçê to continue to close the Squelch beyond
Point I criticize, voçê will be diminishing
senssibilidade of the Squelch and being thus,
very weak signs will not make with that
Squelch if unlocks.

6-for justifying to another band it proceeds from the same one
form.

7-é possivel that in places where it has very
electronic equipment voce has that
to close the Squelch almost or total.

3 Selecting a Frequency
Some ways exist to select
frequency:
Entering a frequency for the keyboard
Using the control of Selector
Selecting a memory channel
Pressuring the keyboard key of Call

Entering a frequency for the keyboard

You can enter directly with a frequency for the keyboard. We go to assume
that we desejassemos the frequency of 145.050Mhz

1 Pressione the button of Band to locate the PTT for the Band of VCHcF.
2 If the Radio will be in memory mode or Call pressures the VFO keyboard
key to pass to the VFO mode.
3 Pressione I number it 4. I number it 4 apareçe in the display followed
for some strokes what it means that we are in mode to type a frequency.

4 Pressione numeros 5.0.5 and 0
5 the only dumb radio frequencia it after to enter with the last number
that in ours in case that it is zero (this last number alone can be zero or
five).
If you not to enter with the last number, the pointer will be blinking
after the some time it will go to return the previous frequency

Notes
1- the pacing of frequency for the band of UHF will be of 10 or 20Khz the
last one I type will automatically be placed for zero 2- you to pressure an
invalid keyboard key, the valid part of the typed frequency will be
entered. 3- you keyboard key not to be pressured some during 10
Segundos(when in mode of frequencia insertion), the radio will come back
the previous frequency.
4- you the VFO keyboard key to be pressured during the input of Frequency,
when in the display still he will be being shown the stroke of frequency
insertion, the radio alone modifies the typed part and mantera the
remainder of the previous frequency.

If the frequencia pacing will be of 12,5 or 25KHz, the insertion mode
finishes in casa(ou types) of 10KHz. For example let us say that we are
with the pacing justifd for 12.5KHz and are entering with a frequency of
438.310MHz ai we type the 3 the 8 the 3 the 1 and at this accurate moment
the radio finishes the mode of frequency input and places in the display
the frequency of 438,312,5. Now it sees in the table to follow when the
pacing will be of 12.5 or 25KHz the consequência of the number entered in
the house of 10KHz.

Keyboard key Frequency Uses a keyboard Frequency

0 00 5 50
1 12.5 6 62.5
2 25 7 75
3 37.5 8 87.5
4 37.5 9 87.5

Using the Selector control
The Selector control can sequentially select frequency for top or low.
It turns the clockwise Selector button in or the Counter-clockwise one
until arriving in the desired frequency.

4. Selection of the size of Passo

The device must be in mode VFO so that it is possible to be justifd Passo.
When you turn the selector button in VFO mode or exactly when the radio is
looking a frequency in automatic mode (SCAN), it jumps of a frequency for
another one of sequential form and this skip is called pacing, and us we
can program this pacing:

1. He pressures keyboard key F for more than 1 second and pressures
keyboard key 3. The current size of Passo will have to be being indicated
in the display.

2. It turns the Selector button to select one another size of Pacing until
it is shown in the display.

3. It pressures any keyboard key except POWER, LAMP and MONI.

The display will vote to the frequency mode alone that now with the size of
the modified pacing.

Mudandanças occured in the Frequency due the alteration of the size of
Passo

Values exist Frequency that in so great determined one of Pacing will not
be possivel to be selected and in this case when voce to modify the size of
Passo will be able to occur a rounding in them you finish houses of the
frequency and when you it will return from the programming mode of the size
of Passo will be able to have occurred this detail.

For example it imagines that we are with a frequency in the 439,920 VFO of
MHz and with a size of 20 Pacing of KHz. If we to change the size of Passo
to 12.5 KHz when to sairmos in the mode of smoothing of the size of Passo
we pass to have the frequency of 439,925 MHz in the VFO.

5. Programming limits
of frequency for the VFO

This radio is provided with a function capable to inside limit the
selection of frequency of bands of 1 in 1 MHz.

For example we go to say that we desire that the radio is with 144,000 the
VFO limited of MHz to the 145.995 MHz or either since that programmed for
this it more podera atravéz of the VFO will not exceed these limits.
Perhaps if you it will have some frequency in some channel of memory or
CALL, above or below of this limit, the same will continue being able to be
used normally.

To program the limits of the band of VCHcF or UHF it selects the band
desired and it initiates the sequência to follow:

1. Correspodente to the inferior limit in ours selects the frequency case
(144)

2. It for more than pressures and it holds keyboard key M 1 second, and
after that it pressures the keyboard key of I number 1. This makes with
that the inderior limit is established.

3. Case selects the corresponding frequency to the upper limit in ours
(145)

4. It for more than pressures and it holds keyboard key M 1 second and
after that it pressures the keyboard key of number 2. With this you
establish that the upper limit is up to 145,995

5. To confirm the limits you are enough to try to type a frequency that is
is of the same ones or to turn the selector button in the route of one of
the limits and memso will not consiguirá to exceed the limits.

To clean the programming of a RESET in the VFO

OPERATION IN TRANSMISSION MODE

CARE:
Before initiating the transmission it verifies if the antenna duly is
connected to the radio or if you this using one another antenna is certifyd
of that not ha no problem with the same one and that it is really for this
purpose. Therefore any probelma in this direction will be able to damage
serves as apprentice it final of harnesses of its radio. E still before
transmitting in one definitive frequency is certifyd of that the same one
is free and not busy.

1. To transmit it follows these pacings:
1. It selects a frequency to transmit.
2. It waits a little before transmitting to certify itself of that the same
one is not being busy.
3. It pressures button PTT located in the left lateral of the radio. The
transmission pointer must light in the red color, and the inicadora scale
of sign will have to indicate the voltage of the battery.

4. It is I recommend to a distancia of approx 5 cm to speak in the
microphone. Bigger pitches or to use the microphone of form leaned against
the lip can not give an audio one in the very satisfactory transmission.
5. It frees the PTT to return to the normal mode. The transmission pointers
had had to come back to the normal one.

2. Changing the power of Tranmissão.
It pressures keyboard key F and after that it pressures keyboard key D/low
so that of this form he is possivel to modify the saida power of. Each time
that to desire to modify for a new saida power of repeats this pacing, and
the viewfinder will give to the indication atravéz of a small " L " and one
to it " and " or if not to indicate nothing where power we are operating
when in transmission.
Each Band can be with a different power at the same time. E the indications
will be always of the band who will be with the lighted pointer of PTT.
When to appear a small E followed for a L this means of that we are
operating with the super power economic decrease and. Power this, used for
communications of distancia shortness with vision string

When in the viewfinder to appear only the L, it is sign of that we are
operating the radio with low harnesses.

When this will not have no pointer indicates that we are using the power
maximum to transmit, and this power podera to vary as the used or when used
battery a external energy.

3. Constraint of transmission
If you the one to desire will be able to stop the PTT of form that it does
not transmit when he will be pressured, thus being able to guarantee itself
not to have an accidental transmission.
To activate and to disactivate this function pressures keyboard key F and
after that it pressures keyboard key F2/tx.s.

4. Time of transmission
automatic (TOT).
This radio already comes programmed with a function that automatically
disarms the carrier after 10 minutes. This function serves to protect the
period of training of power of the radio.

USING THE MEMORY
1 Memory of security of the microprocessor.

All the data that are in the channels of memories are kept in a called
memory EEPROM. E it is capable to keep all exactly the data when the radio
is long periodos without energy.
All the other data are restrained in a common memory and are kept why a
battery of Lithium exists internally that will be able to supply to energy
up to 20 days if the radio to come to be without total energy.

If by chance you to keep its radio for more than that 20 days without
battery and external energy probably voce tera the battery of Lithium total
unloaded and so that it carregue will be necessary again 10 hours from the
rank of the Ni battery Compact disc or the external cable of energy to be
able to be total loaded.

2. Inicializando the memory
ATTENTION:
THE COMMANDS TO FOLLOW DELETE ALL THE DATA OF THE CHANNELS OF MEMORIES.

It pressures and it holds keyboard key M and it binds to the radio atravéz
of the POWER keyboard key until the display shows to all the possible
information, ai liberates keyboard key M. This function is called total
RESET.

Initial values and parameters

Initiating VFO (RESET).
It pressures keyboard key F and it binds to the radio atravéz of the POWER
keyboard key, made this the memory of the VFO will have to be with its old
destruidos data and has initial values and parameters now. In this
operation the clock data are not lost, messages, memories of dialing
(DTMF), limits of VFO and SCAN, codes of PAGING and memory CALL.

3. Channels of memories

This radio comes provided with 50 channels of memories, being that the
channel of I number 1 (Hum) is used to memorize a frequency which we will
desire to use the function of Alarm of with priority channel as we will see
more ahead.

4. Content of the memories.

The channels of memories can store given varios alem of the frequencies,
see to follow:

5. Entering given in the memory.

When we use some vêzes one definitive frequency is interesting that to let
us place in one definitive channel of memory therefore is enough to call
the channel and it will be the disposal.

Entering with a normal Frequency in a memory channel.

1. It selects the frequency desired, offset and other information that you
desja to store in set with the frequency
2. It pressures keyboard key M. The pointer of the number of the memory
will have to be blinking.

3. It uses the numerical keyboard to select a memory channel (0~ 49). It
always types two digitos to select the memory former: 02 for memoria 2.
4. It pressures keyboard key MR to finish the memorization.

Cleaning and removing a memory channel
It uses this procedure to clean a memory channel individually.

1. It selects the memory channel to be clean.

2. It for more than pressures keyboard key M 1 second and after that
keyboard key MR.
3. I number it of the clean memory is removed of the display.

6. Entering with two frequencies one for transmission and another one for
reception in memso memory channel (SPLIT).

1. It uses the numerical keyboard to select the frequencia of reception as
well as other data that you wants to store together.
2. The number of the memory pressures keyboard key M. will have to be
blinking
3. It uses the keyboard again to select the desired channel of memory
pressuring the two corresponding digitos to the channel.
4. It pressures keyboard key MR.
5. The channel pointer must have extinguished, thus indicating that the
data had been all memorized.
6. It uses the numerical keyboard to select the transmission frequency
7. The channel pointer pressures keyboard key M. will have to be blinking.
8. It pressures and it holds the PTT and after that it pressures the MR
keyboard key.
9. The frequency of transmission already this memorized and the radio comes
back to the normal state.

Confirming the contúdo of the channel of double frequency.
1. It pressures the MR keyboard key. The reception frequency must appear
together in the display with the indication of the sign (+/-).

2. It pressures keyboard key F followed for SHIFT/rev or pressures the PTT
to verify if the frequency of transmission this correct one.

7. Entering with a frequency in the CALL channel.
1. It uses the numerical keyboard to select a frequency, and it selects
tambem all the data that to desire to memorize.
2. It pressures keyboard key M and after that keyboard key CALL so that all
the data are memorized.
3. If to desire to memorize a different frequency for the transmission
selects the TX frequency
4. It pressures keyboard key M.
5. It pressures and it holds the PTT. button and it pressures the CALL
keyboard key
6. It liberates the PTT button.

8. Calling the Channels Memorias
It pressures keyboard key MR
If you to desire to move of memory channel can use one of the two methods
to follow.

Using the selector control.
It turns the clockwise control in or the counter-clockwise one until it
appears the desired channel.
Using the numerical keyboard.
It selects a memory channel atravéz of two digitos or either for example:
If to desire to go for the channel of
memory 2 is enough to type 0 and 2.
If you it will be with installed unit ME-1, you will not consiguirá to have
access the memories above of channel 99 for the method of digitação.
however if you it will desire will be able will activate a function that to
the invéz of two digitos passes will operate it seleçao of the channel with
treis digitos, is enough to follow the following pacings.

1. It pressures keyboard key MR and it binds to the radio atravéz of
keyboard key POWER.
The display in the VCHcF band will be in programming mode.
2. It turns the button of selector until apareçer I number it -3.
It pressures any keyboard key to return to the normal mode.

9. Passing data of the Memory for the VFO.
It pressures keyboard key F and after that keyboard key VFO to copy given
of one definitive same channel or of the CALL for the VFO.
Attention:
If you to pass a value of frequency it are of the limits of the VFO, when
you will be to vary the frequency the same one will come back to the
limits.

14. Characters to indicate the memories.
Its radio is capable of instead of using numeros to indicate the channels
of memories it can use up to six characters for memory to give to names the
memory. Sào valid characters the numeros of 0 to the 9 and letters of to
the Z.
Justifying the function:
It pressures and it holds the keyboard key f2 and it binds to the radio
using keyboard key POWER.
NOTE:
When you to use this function its radio will be with only 25 disponiveis
memories the others 25 seram used to aramzenar the alphanumeric data and to
return to the mode of 50 memories repeats finishes it operation.

Registering characters.

1. It pressures keyboard key MR.
2. It selects the desired channel of memory with the chosen frequency using
the selector one or typing I number it of the channel.

3. It pressures keyboard key M and it pressures the keyboard key f2 to
enter in mode to program the characters.

4. It enters with the alphanumeric characters typing the combination of two
keyboard keys, this sequencia will result in one of the six desired
characters, and you to be able to know the combination of two keyboard keys
that had resulted in caracter it sees the table of the pagina ___.
5. If voce to enter some to caracter desired does not pressure keyboard key
VFO and returns to pacing 4.
6. It pressures keyboard key MR to lock up.
7. If you to desire to program given alphanumeric for other memories
repeats the pacings of 2 to the 6.

NOTE:

You it will only be able to place characters for a maximum of 25 channels
of memories.

If a memsagem will be specified for a memory it will be shown always that
the memory will be requested.

If you to need I number it of the channel it pressures and it holds
keyboard key F and it pressures the keyboard key f2.

Cancelling the alphanumeric mode for one determined memory.

1. It locates in the desired memory.
2. It pressures and it holds keyboard key M no matter how hard 1 second and
pressures the keyboard key f2.
The menssagem is cancelled and the memory channel is novamenete indicated
by its numbers correspondent.

MODE OF AUTOMATIC SEEK
((SCAN))

Smoothing initially the Squelch for the critical point, só.assim the Scan
podera to function adequately. You cannot use in set the functions of
Alarme (T.alt) and the Paging mode. The automatic mode of seek functions
independent for the two bands.
To change the route of the seek is enough to turn the selector button or to
use a keyboard the MESSAGEM button.

1. Programming the constraints of the Scan.
This transceiver this provided with two ways to stop the Scan when this to
find a frequencia being used.

Burst Scan for time.
In this mode its radio will always make a break that to only locate a busy
frequency that it will remain only 5 seconds and if you not to interrupt
the Scan it must continue the seek for another busy frequencia thus
successively.

2. Burst Scan for the Squelch.
In this mode its radio will start to be burst for the sign received from
form that while the sign present in one will be determined frequency the
Scan is interrupted temporarily.

It to come back to make the automatic seek will be necessary the ausencia
of the sign for more than 2 seconds or you he will need to turn the
selector button for the desired route.

If voce will be using function CTCSS the Scan alone will stop will have
detected the correct sub-tone.

If you the Scan will be using function DTSS will always stop that a sign
will be detecato and exactly receiving codes from DTSS it will not be
interrupted waiting a code or the ausencia of the sign for more than 2
seconds to be able to come back to the seek mode.

The combination of the CTCSS and the DTSS when the Scan will be activated
will need the sub-tone first and when this will be detected it will
interrupt the seek and will wait for the DTSS code to open the Squelch.
from the the opposite it comes back to the mode of automatic seek.

Selecting the types of scan

The transceiver when still not programmed for another mode of Scan this in
the mode of burst seek for time. To alternate the mode it follows the
following pacings:

VCHcF BAND
She pressures and she holds keyboard key 8 and she binds to the radio
atravéz of the POWER keyboard key.

BAND of UHF
She pressures and she holds keyboard key 9 and she binds to the radio
atravéz of the POWER keyboard key.
2 Cancelling automatic Procura (SCAN).
In the main band:
It pressures any keyboard key except MONI, LAMP, BAND MHz, E.chg, or MSG.
In the sub-band:
It pressures the BAND keyboard key and it pressures the PTT

3. Options of Scan
The options are the following ones:

Scan of memory
The seek of automatic memory is inicializada when we pressure the MR
keyboard key for more than 1 second.
Memories with constraint will be jumped in the mode of automatic seek.
To bind the constraint in one definitive memory we select the memory
desired and Pressures keyboard key F and after that it pressures keyboard
key 0/l.out. It repeats the operations previous if to desire to stop plus
some memory.
In the display it will have to appear one what it indicates that the
channel this with a constraint to be jumped in mode of automatic seek.

To cancel the constraint it locates the channel with the same one and
pressures keyboard key F followed for keyboard key 0/l.out.

Scan of VFO
In this mode you can make the automatic seek for the frequency of
sequêncial form.
To be able to make the automatic seek in mode VFO for the frequency you are
enough to justify the critical point of the Squelch and to pressure for
more than 1 according to keyboard key of VFO and the automatic seek is
inicializada together with a piscante point in the house of the MHz to
indicate the mode of Scan. If you to desire to change the direction of the
seek is enough to turn the selector one for a contrary direction.
Scan of VFO with limits.
As well as you you can program limits for the VFO you can also program
limits for the mode of automatic seek.

You can have a limit for each Band and when in this mode the Scan makes the
seek only inside of the band established in the program.

**time-out** to can program some limit of Scan follow the pacing following:

1. He pressures the button of Band for the desired band.
2. He selects the frequency that will go to determine the upper limit for
the Scan.
3. He pressures keyboard key M for more than 1 second and pressures
keyboard key 5.
4. He selects the frequency that will determine the inferior limit of the
Scan.
5. He pressures keyboard key M for more than 1 second and pressures
keyboard key 4.

NOTE:
When you reset of VFO to give to one the limits of scan seram lost for both
the bands.

Confirming the limits of Scan.

It pressures keyboard key F for more than one second and pressures 4
keyboard key done this the display will have to show the frequency that
determines the inferior limit.

It pressures keyboard key F for more than one second and pressures 5
keyboard key done this the display will have to show the frequency that
determines the upper limit.

Initiating the Scan with limits.

1. It has justifd the critical point of the Squelch.
2. It selects a frequency that is inside of the limits.
3. It for more than pressures and it holds keyboard key VFO 1 second.
A piscante point in the house of the MHz indicates that we are with the on
mode of automatic seek.

Scan in the house of the MHz
Its radio when in mode of special automatic seek and the Scan of VFO this
is capable to make the seek inside of a band of 1 MHz being enough you to
pressure the keyboard key of MHz exactly when the radio will be in mode of
Scan of Former VFO.:
If you it will be scaneando and to pressure the keyboard key of Mhz when
the radio will be in 147e some thing, it will go to be scaneando of 147 á
148 and to come back to the normal one pressures the keyboard key of Mhz
again.
Alternating Scan VFO/mr.
This function makes with that the radio pass to look the busy frequency
enters the frequency of the VFO and útimo used channel of memory.
1. It has justifd the Squelch for the critical point.
2. It pressures keyboard key F and it pressures keyboard key MR.
3. The seek is made of form alternated between the VFO and it finishes it
used memory.
9.Scan alternated CALL / VFO
This function is identica the previous one and alone it of VFO for the CALL
differs that the Scan to the invéz to alternate of the VFO for the
alternating memory.
1. He pressures the VFO keyboard key.
2. He pressures the keyboard key of CALL 1 for more than second. E the seek
for a busy frequency between the VFO and the CALL if inicializa.
10. Alternating Scan CALL/mr
As previous only that alternating between the CALL and last channel of
memory.
1. It pressures the MR keyboard key and it selects the memory desired.
2. It for more than pressures keyboard key CALL 1 second.
11 alternating Scan VFO/mr/call
1. It pressures keyboard key F and it pressures keyboard key CALL.
2. The VFO more I finish it memory channel and the CALL is alternating to
make the seek for a busy frequency.

12. Function of Alert (With priority)
This function when active he makes with that the radio pass to monitor the
memory channel numbers 1 of form that if you will be for example in the
CALL, it will go of 5 in 5 seconds until the memory channel 1e will be busy
it will emit a short Beep, of this form you can practically be monitoring
two frequencies at the same time and without confusing the current one.
1. He has justifd the Squeclh for the critical point.
2. It pressures keyboard key F and it pressures keyboard key 4 and pointer
AL will appear in the display.

3. If it will have a present sign in the memory channel 1 you will hear a
Beep.

4. To disactivate repeats pacing 2.

If in the channel the 1 memory will be with CTCSS the CTCSS will be
rejected.

Memory channel 1 also is monitored when the display shows the two or only a
band.

OPERAÇAO IN REPEATERS
1. Transmitting in repeater mode (Offsets + or -).
All repeating of radioamadorismo it is used of two frequencies one to
receive and other to transmit. E for each band exists a standard. To this
operation we call Offset of frequency. Its radio Already comes with the
value of the Offset programmed in its microprocessor being enough in some
versions to only indicate its route. In the American version this route is
placed automatically.

ROUTE UHF VCHcF
+ + 600 KHz + 5 MHz
- - 600 KHz - 5 MHz

2. Selecting a route
of Offset.

It pressures the SHIFT keyboard key. If you to pressure keyboard key SHIFT
some times will go to notice that he is possivel to alternate of route
always that to desire them to me, and it is enough to verify in the display
the corresponding route the repeater that we desire to use.

3. Automatic selection of the Offset.

Version the USA and Canadian

If its radio will be of American procedencia and provavel that it is of the
version series K and in this case it already comes programmed of plant to
place the route of the Offset automatically as the standard established for
the American ARRL(Liga of Amadorismo Radio). In this case if you to desire
to modify the route are enough to pressure keyboard key SHIFT.

Valley to remember that in VCHcF in them we use the same standardization of
Offsets that the Americans.

Cancellation of the automatic Offset.

It pressures and it holds the BAND keyboard key and it binds to the radio
atravéz of the POWER keyboard key to activate or to disactivate the
automatic mode of Offset.

. Manual selection of the value of Offset.
The value of Offset can be modified for one another different one of the
normal standard that in this case already comes programmed. E you can
inside select a value of 0 up to 99,9 MHz of 100 in 100 KHz.
1. He pressures and he holds keyboard key SHIFT/rev and he binds to the
radio atravéz of the POWER keyboard key.
2. He for more than pressures the keyboard key of F 1 second and after that
he pressures keyboard key SHIFT/rev and in the display he must appear the
current value of the Offset. He turns the selector button to select the new
value of Offset.
3. He pressures any keyboard key of the board to return to the normal mode.
If voce to give to a Reset of VFO or Memory this will make with that the
value comes back to the normal standard.
NOTE:
If you it will have selected a value high of Offset and this to exceed the
VFO limits when it will be to transmit the radio will emit a Beep and will
cancel the transmission.

5. Inverted function (reverse)
As when we are using a repeater in the truth we are using a frequency to
transmit and other to receive would give work very if by chance we
desejassemos to verify if in the transmission frequency we poderiamos to
hear to another station with which we are speaking or either in the input
of the repeater where our transmissions are being made. But that is
facilitated atravéz of the function of Reverse that nothing more makes of
that to invert the frequencias or either of transmission starts to be of
reception and vice it turns and it is enough to pressure followed keyboard
key F of keyboard key REV that in dispaly will appear a R indicating that
we are in inverted mode.

If to desire to come back to the normal mode is enough to repeat the
operation.

6. Operation with Tone
Some repeaters require to be set in motion one definitive together tone
with the transmission therefore if the same it will not be present in our
transmission will not be possivel to set in motion the repeater.

Selecting a tone frequency.
If you possivel will not be with installed optional unit TSU-7 not sera the
selection of the same ones.

1. It for more than pressures keyboard key F 1 second and after that it
pressures keyboard key TONE. At this moment it must appear in display one
of the 38 possiveis frequencies of sub-tone.

2. It turns the selector button to select one of the 38 frequencies

3. It pressures any keyboard key to leave the selection mode or waits one
ten seconds that the radio comes back to the mode of normal display.

Operating the function of Tone
It pressures keyboard key TONE. A small " T " will have to be being shown
in the display of the band where we will be with the PTT.

7. Operations in Autopatch. (Telephone coupled automatically for the
Radio).
Some repeaters possess a job of automatic Telephony.
To be able to use the features of this system its radio comes provided with
some keyboard keys that if pressured when in transmission they make with
that the radio transmits standards DTMF necessary to control the Patch
(control interface).
The numerical keyboard is used in the transmission as a keyboard of
telephone with the unica difference of that we have 4 keyboard keys more
than is A, B, C, D.

To activate the keyboard.
It pressures the PTT keyboard key.
It pressures the appropriate keyboard keys of the numerical board for its
use.
NOTE:
To activate these jobs exist a sequência of codes and in the case of a
repeater you need to be part of the group of mantenedores of the same one.

Selecting the retardation time.
When we pressure the PTT and after that we pressure some alphanumeric
keyboard key of the board, if to free the PTT soon after that the radio
comes back instantaneamente to the reception mode but if to want that to
the invéz of it it to return from imediáto still remains per two seconds

that is possivel and util therefore we can type a sequencia of keyboard key
in mode of transmission without being holding the PTT button and thus that
to finish to enter with the sequência of last digitos 2 seconds of finishes
pressured keyboard key the radio comes back to the reception mode.

1. It disconnect the radio
2. It pressures and it holds keyboard key 2 and it binds to the radio
atravez of the POWER keyboard key.
3. liberate the keyboard key number 2.
4. If you to quizer to come back to the normal one repeats the pacings of 1
the 3.

8. Memory of DTMF

Its radio comes provided with ten memories to store up to 15 digitos of
DTMF for memory. These memories are useful when we desire to store codes of
control of the Patch or to store numeros of telephones.

Storing codes DTMF

1. It pressures keyboard key M and after that it pressures the MHz keyboard
key to select the insertion mode.

2. The alphanumeric keyboard enters with the digitos of DTMF pressuring.

3. It pressures keyboard key MR after to have entered with the sequência of
DTMF.

4. It selects one I number of 0 to the 9 to determine in which of the 10
memories you wants to store its sequência. Made this the radio comes back
to the mode of sequência selection.
5. If you to enter with I number it wrong it pressures keyboard key VFO and
it returns to pacing 1.

6. To leave in this way memorization of DTMF it pressures the BAND keyboard
key.

Verifying codes DTMF stored in the memory.

1. It pressures and it holds keyboard key F for more than 1 second followed
of the keyboard key of MHz.
2. The memory pressures the corresponding numerical keyboard key and the
codes had had to be shown in the display.

Sending a code DTMF.

1. It pressures and it holds the PTT button.
2. It pressures the keyboard key of MHz followed for one I number of 0 to
the 9.
3. Code DTMF will appear in the display.

OPERATIONS WITH CTCSS.

The unit of CTCSS (TSU-7) is incluida in only some models of the American
and Canadian version.
The installation of optional unit CTCSS (TSU-7) this explained in them you
finish paginas of this manual.
CTCSS System of Burst Squelch for Continuous Tone, this function when
activated it makes in that the radio pass to control the Squelch atravéz of
the received Sub-tone or either so that the Squelch opens will be necessary
to receive with the transmission from who this together wanting in
requesting one to them of the 38 frequencies of sub-tone.

Selecting the Sub-tone

To select or to choose one of the 38 different sub-tone that will go to
control our Squelchs sees the procedure in pagina 16.

Operating with function CTCSS.

1. It pressures the keyboard key of BAND of the desired band.
2. It pressures keyboard key F and after that keyboard key 3. In the
viewfinder it must appear a small CT thus indicating that this atic\va the
CTCSS function.

The appointed band operates now in the mode of Tone Squelch.
To justify the function for another band she repeats the pacings previous.
In Dual mode the CTCSS controls the two bands in reception but when in
transmission it disconnect temporarily the CTCSS of the other band.

BURST SYSTEM OF SQUELCH FOR DTSS

When in DTSS mode squelch is burst atravéz in this way and so that the
Squelch opens it will be necessary to receive 3 codes from DTMF previously
programmed.
An open time the Squelch after to receive the combination correct from the
3 DTMF you can normally hear the station that is calling to it. E when you
not to receive more sign for approx 3 seconds the Squelch again starts to
be burst for the DTSS. Valley remembers that when in this mode the radio
will go to always transmit the 3 DTMF programmed that to pressure the PTT
and also when we return to the reception mode the radio comes back to be
burst for the DTSS.

1. Codes of DTSS

You can select sequencias of codigos of 000 to the 999 what of the total
one of 1000 different codes. E you will be able to store a different code
for each channel of memory or a channel of CALL.

Chosen team codigos of DTSS.

1. He pressures the BAND button to select the Band desired.
2. He for more than pressures and he holds keyboard key F 1 second and
after that he pressures keyboard key 2/dtss.

3. He enters with the sequência of treis digitos for the keyboard.

NOTE:
If to vocêpressionar a not numerical keyboard key or if you to be without
pressuring nothing during 10 seconds the radio will return to the normal
mode.

2. Using function DTSS.

1. It pressures the button of BAND of the desired Band.
2. It pressures keyboard key F followed for keyboard key 2/dtss. In the
viewfinder will have to appear in the display a small pointer DT of
activity of the function.

3. The Squelch alone will open when to receive the sequência correct from
DTMF.
4. To transmit the sequência of the code it pressures the PTT and it second
will be transmitted in first the 0.5.

NOTE:
During the transmission of the codes the radio does not transmit its vóz.
If it recommends disconnect the function of battery protection (SAVER) when
will be to use the DTSS.

5. It pressures keyboard key F and it pressures keyboard key 2 to cancel
the DTSS function.

NOTE:
If you to use function CTCSS in simultaneous set or with the one of DTSS a
time before being sent the codes will be nescessário to open the CTCSS.

3. Using the DTSS atravéz of the repeater.

When we pressure the PTT is transmitted codigo immediately and if we will
be to use a repeater is possivel well that we have the problem of when the
repeater to relay our sign the DTSS code already to have been sent,
therefore the repeater takes some seconds stops to enter in transmission
mode.

To skirt this situation the radio already comes provided with a function of
retardation also known by Delay that atraza the transmission of the code
always that we will be in duplex mode. This time of retardation and 250 ms
but if to desire we will be able to magnify for 450 ms.

Changing the time of Retardation.
1. It disconnect the radio
2. It pressures and it holds keyboard key 1
3. It binds to the radio atravéz of the POWER keyboard key.
4. It liberates keyboard key 1

SELECTIVE CAHAMADA
(PAGING)

The Paging uses as well as the DTSS DTMF codes to control the Squelch of
similar form to the DTSS. It is only different therefore alem to control
the Squelch as the DTSS it is capable to indentificar the station that this
in calling and still is possivel terms a group where each one can have its
proper code and of this form to be bothered when integrant one of the group
will be requested another or if still to desire could not always be
requested all of one alone time and everything with the indetificação of
the station that this calling.

1. Memory of codes of Paging.

The codigos are 8 Memories of storing tosos that to desire.

2. Justifying codes of Paging.
It initiates the programming for its individual code.

1. It pressures keyboard key F followed for keyboard key 1 to enter in mode
of Paging.

2. It pressures and it holds keyboard key F for more than 1 second followed
of keyboard key 1 to enter in smoothing mode.

3. It turns the selector button until selecting (its individual code).

4. Its individual code of 000 to the 999 enters using the numerical
keyboard.

5. Its code of ID is memorized in the memory.
6. It selects of 1 to the 6 with the selector button.
7. Pacing 4 enters with a new code of in agreement Paging.
8. It pressures any keyboard key to leave the smoothing mode of the codes.

The Graph below shows an example of as we can use the Paging with a group
of friends and it it will serve of example better to understand the
functioning of the function of Selective Call.

NOTE:
Its code of ID (Identificação) this in its radio
gift in the memory and the each member has a code
Proper ID also in its respective memories.

3. Transmitting a code of Paging (Calling a station).

1. It selects the frequencia desired.
2. It pressures keyboard key F followed for keyboard key 1 to enter in mode
of Paging. It will be necessary that another radio also is in mode of
Paging.
3. It pressures and it holds keyboard key F for more than 1 second to enter
in the mode of selection of a code of Paging.
4. I will choose one of the codes previously stored for the call of the
desired station.

Calling all the members simultaneously.

It selects the memory that contains the code of the group. In ours example
case memory 5.

It pressures the PTT. The communication is possivel in such a way in Paging
mode as in mode of one selection codigo.

The code of group 789 followed by a asteristico to separate to the two
codigos more codigo 111 is transmitted.

Calling a specific member the group.

1. It pressures keyboard key F for more than 1 second followed for keyboard
key 2,
2. It selects the memory that to contain the code of the desired station
for example member 3. E if by chance we do not tivessemos memorized this
code we utilizariamos memory 0 to place code 444.
3. It pressures the PTT.
4. You can cancel the mode of Paging an established time the contact if
desire.

Codigo of station 444 separate for a asterístico and followed by individual
its codigo (ID) is transmitted always that pressured the PTT.

5. Receiving a code or a member from the group.

1. It syntonizes the desired frequency.
2. It pressures keyboard key F followed for keyboard key 1 to entar in
Paging mode.

Receiving a code from individual Paging.

1. When an appropriate code is received, its Squelch is opened and an alarm
is sounded for the speaker.
2. If the station that called to it sent its individual code (111) and goes
to assume that the station that called to it is of 3 member then the
display will have to be as of fig below.

3. It pressures the PTT to answer the station that called to it and the
code of memsma will be sent automaticamrente.

Receiving a code in group.
code that makes to open the Squelch of all the members.
1. If one of the members to transmit a code of group in our example (789)
it will be making with that all members receive its sign in this in case
that all the members had had to be with its display showing number it of
the memory which this codigo of the group followed for the P of Paging more
codigo of group (789) and if you or the other members to desire to know who
this calling general form is enough to turn the button of selector stops
until memory 0 and there it will have to be the code of the station
solicitant or if to prefer pressures the PTT for answering the same one,
therefore in this way the radio transmits the code of the station that it
requests separate asterístico followed for its codigo (ID).

NOTE:
If in the display to appear one and means that the sign this enough good
one not to be able to be decoded and thus it places one and of indication
of ERROR.

NOTE:
For one better efficiency disactivates the mode of Paging after to
establish the beginning of the contact.

5. Cancelling the burst Squelch for the Paging but continuing in the mode
of Paging.

If you to desire to cancel the control of Squelch contolado for the Paging,
that is possivel and util when we want to use the Paging to only identify
the station that this in calling and to leave the use of Paging as a
privative channel of side.

Cancelling the control of the Squelch

1. It pressures and it holds keyboard key F for more than 1 second followed
of keyboard key CALL.
2. To return to the burst Squelch for the Paging repeats the operation
previous.

6. Blinding memorized codes already

If you to desire will be able to inhibit some memorized codes already in
the memories of Paging, for example: In its in case that each time that a
member was requested of that they are memorized of 1 to the 5 its Squelch
would open, or you it would have that to remove the colocalos codes of the
memory or then nor with exception of the one of group (789), but let us say
that hour if desires and hour if does not desire to listen to other members
voce will be able to temporarily inhibit the desired memories.

1. It selects the memory to be blinded.
2. It pressures followed keyboard key F of keyboard key 0. The display must
show one to indicate that the memory this blocked one.
3. To unblock it repeats pacings 1 and 2

TRANSMITTING AND RECEIVING MESSAGES

Its radio is capable to transmit and to receive messages in the inferior
part from dispaly and it uses a combination of DTMFs for the formation of
alphanumeric characters.
You can store up to 10 memsagens received each one with up to six digitos
what she totalizes 60 characters, however if to receive more from the one
than 10 memsagens we will be able to program the radio so that she overlaps
the first memsagens received from this form we will not lose nehuma current
message case the memories are full.
Alem of that you they dispoem of 10 memories to store messages programmed
daily pay to send at any time and more four already programmed of plant for
general use.

NOTE:
This function is used in set with DTSS and PAGING.

1. Modes to send messages.

Two ways of if sending messages exist.

You can always transmit its message manually for the keyboard being enough
for this that to initiate and to finish a message to type #.

he sees the table equivalence each to caracter.
each message can contain in the maximum 6 characters.

Or if to prefer will be able to store up to 10 messages in the message
memories and when to want podera uses them.

2. Using the memories of Message.

Procedure of programming.

1. It pressures keyboard key M followed for the MENSSAGE keyboard key to
enter in the memorization mode.

2. The sequencia of combinations of DTMF enters with its message typing.
3. It pressures the VFO keyboard key if to enter with some caracter wrong
and returns to pacing 1.
4. It pressures keyboard key MR followed for I number it of 0 to the 9 that
it corresponds the desjada memory to store the message.
5. To cancel the mode of message input it is enough to pressure the PTT.

3. Checkando the messages.

1. It for more than pressures keyboard key f 1 second.
2. It pressures keyboard key MESSAGE.
3. The memory pressures the corresponding numerical keyboard key to be
verified (0 to the 9).

to caracter operation

0 0
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
EQUIVALENCE TABLE:

to caracter operation

Q 1+a
THE 2+a
D 3+a
G 4+a
J 5+a
M 6+a
P 7+a
T 8+a
W 9+a
to caracter operation

Z 1+b
B 2+b
E 3+b
H 4+b
K 5+b
N 6+b
R 7+b
U 8+b
X 9+b

to caracter operation

SPACE 1+c
C 2+c
F 3+c
I 4+c
L 5+c
THE 6+c
S 7+c
V 8+c
Y 9+c

FOR EXAMPLE:
6+c
4+c
3+a
6+a
2+b
2+a
B M D I

4. Transmission of the messages stored in the memories.
1. Presione the PTT followed for keyboard key MESSAGE. The message pointer
must be appearing in the display.
2. Still with the pressured PTT it pressures a numerical keyboard key which
corresponds the desired memory.
NOTE:
When you it will be hearing the message being transmitted you can liberate
the PTT that it does not interrupt itself until its end.

5. Receiving a message.
1. With the function of DTSS or active Paging it pressures keyboard key F
followed for keyboard key MESSAGE.
2. Simbolo of message is shown in the display and when you to receive some
it will see the same one to appear in the display and simbolo of message it
will be blinking.
mode DTSS

mode of Paging

6. Messages received in the memories
It pressures the MESSAGE keyboard key and it finishes it received message
will be shown in the viewfinder and in case that it has more is enough to
turn the selector button to be able to read excessively.
When not reprogramado:
If the 10 memories will be full of messages it will store the new message
always in memory 0 thus to preserve the others nine first messages.

If you to desire podera to modify this finishes function so that when the
10 memories will be full the radio more does not memorize no message.
To move for this mode it pressures and it holds the MESSAGE keyboard key
and it binds the radio.

Cleaning the message memories.

It pressures and it holds keyboard key M for more than 1 second and
pressures keyboard key MESSAGE.

This clean function nao the memories of transmission of messages.

EXTENDED FUNCTIONS OF RECEPTION

1. System of alarm for tone.

The system of alarm for tone is provided with a sonorous sign beyond a
small bell that when to etiver represented in the display will indicate the
activity of this function and to understand more good of as the alarm
functions goes to say that if we will be using this function all time that
to have a sign in the frequency it sounds an alarm and will place in the
display the hour where he had I finish it sign.
If you to place the T.alt in activity the communications or the signs of
audio did not poderam to be heard.
Its use in set with the functions of CTCSS, PAGING would be interesting, or
DTSS therefore thus if in moving away them from the radio for one
determined time and will be requested will also know the schedule of
finishes request.

When we will be using the T.alt function the APO function is disactivated.

1. It has justifd the Squelch for the critical point.
2. It pressures followed keyboard key F of keyboard key 5. The pointer of
this function must appear.

3. Pointer T.alt must blink and a Beep will have to sound in case that some
sign is received or in case of CTCSS, DTSS or PAGING to have decoded a
sign.
4. The hour of finishes request will have to aprecer in the display.
5. It pressures the PTT to disarm the T.alt (in the case to only have
itself received a sign from the the opposite the PTT is blocked).
6. It pressures keyboard key F followed for keyboard key 5 to disactivate
this function.

NOTE:
It T.alt to be able to be set in motion in the case of if being using
function CTCSS will be necessary the presence of a sign with the correct
sub-tone for more than that 1 second.

Selecting different sounds of alarm.

It pressures and it holds keyboard key 5 and it binds to the radio atravéz
of the POWER keyboard key. In this way alternating you the alarm of Beeps
for a sound similar to the one of vice telephone and turn.
2. Monitor
When pressured it makes to momentarily open the Squelch of the same radio
with CTCSS, DTSS and PAGING.

3. Disconnect the function of Beep of the keyboard.
Its radio produces a Beep to each pressured button and if you desire to
make unusable this function or same she binds it Pressione keyboard key 6
and binds to the radio atravéz of the POWER keyboard key.

4. Lampada (Lamp)
When pressured it makes with that the display and the keyboard if it
illuminates temporarily but if you to desire will be able to make with that
it remains on the time that to desire.
1. It pressures followed keyboard key F of keyboard key LAMP.
2. To cancel it is enough to pressure the same sequência again.

5. Stopped keyboard

If to desire will be able to stop the keyboard all so that it does not
change it accidentally.
When the keyboard to be only stopped keyboard keys LAMP, MONI, E.chg, F+m
and PTT will not be stopped.
To stop and to unlock pressures followed keyboard key F of keyboard key M.

6. Smoothing of volume for earphone.

CARE:
If you use earphone you are provavel well that when will be to place the
phones with the intenssidade of volume that was using to hear for the high
falante of the radio, she can very be high for the phones and also harmful
to its ears. To this case the radio comes endowed with a function that
minimizes the maximum possivel the levels of audio for both the bands
previnindo against one possivel esquecimento.

1. It pressures and it holds keyboard key 4 and it binds the radio.

This operation reduces the volume below of the minimum original volume for
both the bands.

2. It connects its earphone.
3. It has justifd to the volume for a intenssidade confortavel.

NOTE:
This function reduces the level of audio for the high internal falante. If
voce to desire to return to the normal mode is enough to repeat the
operation of pacing 1.

7. Separating the sound of the high internal falante with the hardwired
external microphone.

If you to connect the external microphone the sounds of the two bands will
leave for the external microphone. But if voce to desire to separate audio
of each band you will be able to make with that the audio one of the band
who will be with the PTT she has left in the microphone and the one that
this with the PTT has not left in the very util radio that is when desires
to eliminate microvoices in transmissions full-duplex.

1. It pressures keyboard key F and keyboard key 6 to separate or to mixar
the signs and the radio will give to a message MIX or SEP for each case to
it.

2. It pressures keyboard key F for more than 1 second and pressures
keyboard key 6 if by chance to want to invert audio separate or either the
band who will be with the PTT will be heard in the radio and to another
band in the vice microphone or it turns.

8. Function of change of automatic band.

The function of change of automatic band makes with that when activated,
paase to monitor the form bands that when some sign will be detected it
immediately passes the PTT for the band where the sign was present and
after treis second not having more sign in that definitive band or if it
will not be pressured the PTT returns its previous position.

1. She pressures keyboard key F followed for keyboard key BAND/a.b.c.
The A.b.c. must be indicated in the display.

2. If some sign will be received the automatically commuted PTT and for
this band.
3. If you to pressure the PTT the same will be stopped of the side where it
will be and function A.b.c. will be cancelled.

9. Simultaneous reception of two signs of the same band.

If you to desire will be able to program its radio so that to the invéz of
a band of VCHcF and another one of UHF, you it can have two bands of VCHcF
or UHF.

Simultaneous signs in VCHcF.
1. It pressures keyboard key BAND for the band of UHF.
2. F2 pressures the keyboard key. The band of UHF will have to disappear
and in its place one another band of VCHcF must apareçer in the display.

Simultaneous signs in UHF.

1. It pressures keyboard key BAND for the VCHcF band.
2. F2 pressures the keyboard key. The VCHcF band will have to disappear and
in its place one another band of UHF must apareçer in the display.
NOTE:
Simultaneos signs of the same band make with that the reception performance
loses a little its sensitivity alem of that can be possivel some
interferencias.

10 Disconnect one of the bands.

If you to desire could disconnect one of the bands and be only with a band
in the display.

It pressures keyboard key DUAL to bind and disconnect a band.
If you to preesionar keyboard key BAND with only one band alternating you
for the other band.

11. MHz Mode

You can use this keyboard key to speed a seek or frequency selection when
she will be being made for the selector button, and in this way the pacing
and of 1 in 1 MHz.
Pressuring the keyboard key of MHz you become with that the 100 houses of
KHz delete and if you to turn the selector button to look some frequencia
of 1 in 1 MHz.
To return to the normal one it pressures any keyboard key except E.chg or
it waits per 10 seconds.

12. Display with frequency
canalized.

Its radio can be programmed so that to the invez of if having in the
display the frequency it appears only I number it representative of the
memory channel and of the CALL they alem of that we will not have more the
VFO to be able to vary the frequency. This operaçao is util to stop the
radio in mode of CALL and memory channels.

1. It pressures keyboard key 3 and it binds to the Radio atravéz of the
POWER keyboard key.

2. It must appear in the display some numeros that represent the channels.
E to be moved of channels turns the selector button.

3. To return to the normal mode repeats operation 1.

FUNCTIONS TO SAVE THE BATTERY

1. Mode of preservamento of the load of the battery (SAVER)

This radio comes endowed with a circuit battery economizer to magnify the
life of same and the function that this economizer controls and the SAVER.
When activated the Saver mode the radio passes for a switching process or
either it is binding and disconnect you vary times for second or per minute
and its time of off is bigger of the one than of ligado(aprox. 0,1 second.)
what it makes with that the battery comes to magnify its load time and this
function when activated starts to after enter in activity 10 seconds of it
I finish command or when we are not receiving no sign more than the 10
seconds.
Function SAVER does not have effect when in mode of Scan.
To activate and to disactivate this function it pressures keyboard key F
for more than as and pressures keyboard key MR.

Selection of the preservation time.

1. It pressures and it holds keyboard key 7 and it binds to the radio
atravéz of keyboard key POWER.
2. It selects the time that it remains off at the moment of the switching
atravéz of the selector one: 0.4 - 0.6 - 0,8(initial mode) - 1.0 - 1.5 -
2.0 or 3.0 seconds
3. Keyboard key of the board to return to the normal one pressures qualque.

2. Function of disconnection
automatic.

1. When this function will be active, makes with that the radio if
disconnect 59 minutes of it after finishes received sign or of it I finish
effected command, emitting per one 5 seconds some Beeps.
2. After 1 minute of sounded the Beeps the radio if disconnect being able
to be on atravéz of the POWER keyboard key.

NOTE:
Although when in mode Scan or T.alt the display to show to the pointer of
function APO it will be in the inactive reality.
3. To bind and disconnect it pressures keyboard key F 1 for more than
second and after that it pressures keyboard key VFO.

CLOCK FUNCTIONS

If you to pressure keyboard key F followed for keyboard key 7 will go to
appear in the sub-band a clock. The clock is shown in the form of 24horas.
If you it to pressure the F followed for the 7 will be cancelled of the
display.

1 Justifying the Hour

1. He pressures and he holds keyboard key F 1 for more than second and
after that he pressures keyboard key 7, in this way the shown clock and in
the main band.
2. He has justifd to the hour in the display atravéz of the selector
control.
3. He pressures keyboard key M.
4. He has justifd to the minute in the display turning the selector
control.
5. He pressures keyboard key F to lock up the mode of smoothing of the
clock.

Justifying the alarm

When you pressure keyboard key 0 in mode of smoothing of the clock as
display is clean and the inica tally since the 0 seconds.

2. Function of timer (temporization)

Smoothing of the hour to bind.

1. It pressures keyboard key F for more than 1 second and pressures
keyboard key 8, and in this way the display must indicate a small clock
indicating the mode of smoothing for the hour to league itself
auromaticamente.

2. It has justifd the hour.
3. pressure keyboard key M
4. It has justifd the minute and it pressures keyboard key F.

Smoothing of the hour disconnect.

1. It pressures keyboard key F for more than 1 second and pressures
keyboard key 9, and in this way the display must indicate a small clock
indicating the mode of smoothing for the hour disconnect itself
automatically.

2. It has justifd the hour.
3. pressure keyboard key M
4. It has justifd the minute and it pressures keyboard key F.

Binding and disconnect the functions of Timer.

Pessionea uses a keyboard F followed for keyboard key 8 to bind and
disconnect timer automatic ligament.

Pessionea uses a keyboard F followed for keyboard key 9 to bind and
disconnect timer automatic disconnection.

Each timer it has its propria indicão in the display.

Function of alarm.

If you keyboard key M to pressure two times when in mode of smoothing of
timer of automatic ligament, he will be possivel to bind or disconnect the
alarm turning the selector control for " the ON "

The alarm will sound per ten minutes when the time will be reached justifd
daily pay r'dio to bind it.
Keyboard key pressures qualque to interrupt the alarm

OPERÇÃO IN DUPLEX

Normally the tranceptor operates in duplex with the bands, or either when
we will be to transmit in a band the reception of another one is
interrupted until let us leave to transmit.
If you to prefer it will be able to operate in mode Full-duplex, or either
while it will be transmitting in a band it will be able to hear
simultaneously to another one.
It pressures keyboard key F and it pressures keyboard key DUAL. Pointer DUP
must be appearing in the display thus indicating our mode full-duplax.

To return to the Duplex mode repeats the pacings previous.

If you use a microphone exerno you see the advantages of if using audio
separate and thus diminishing the probability of a microvoice.
If you do not use external microphone or same that uses plus this having
microvoice problem she follows the following pacings.

He pressures keyboard key F for more than 1 second and pressures after that
keyboard key DUAL. Pointer DUP must be now blinking the time all, what it
means the activity of the function explains soon below of the figure.

In this mode the senssibilidade of the microphone more the received volume
of audio passes to be reduced automatically to prevent a microvoice and the
radio passes to the power of saida EL.

If you to desire to modify the power is enough to pressure atecla F+ D/low.

To cancel this function it repeats the operation initial.

PROGRAMMING THE MICROPHONE

If you possue a microphone that in turn has three 3 keyboard keys 1.2 and
you podera programs the same ones with any desired function, except the one
of POWER.

To program it is well simple, it is enough that you with the off radio it
pressures one of the three situated buttons in the upper part of the
microphone and with the same pressured it binds to the radio atravéz of the
keyboard key of power and thus that the radio to bind voçê podera to free
the keyboard key and the display must be indicating a PF followed of it I
number of the button (1.2 or 3) which if this programming. Continuing, voçê
is enough to pressure the keyboard key that voçê desires with that the
button has controlled or will be a secondary function as for example the
selection of one determined sub-tone, then pressures keyboard key F for
more than as and pressures keyboard key TONE, ai the radio will have to
emit a sign and to come back to the normal one. Now when to desire to
modify the frequency of the tone voçê can opt to pressuring the button of
the microphone which we program for this purpose, and in this case the
value of the frequency of the tone will appear in the display remaining
voçê to make the selection atravéz of the selector control.
6